The AV-P2 Output Module is designed to provide a 1- or 2-channel analog output from a 16-channel Pro16® A-Net® stream, easily selected using a front-panel rotary switch. Independent output levels for the left and right channels are set using DIP switches.
Power can be supplied to the AV-P2 with an external DC power supply or over the Cat-5e cable when connected to an A-Net Distributor.
Each AV-P2 Output Module in a Pro16system receives a 16-channel A-Net stream from an input module, console interface card, A-Net distributor, or Pro64® audio network (via the ASI A-Net Systems Interface module). It provides a one or two channel, mono or stereo analog output from that 16-channel digital audio stream.
A front-panel rotary switch allows the output to be set to any one of those 16 source channels. If the selected channel is part of a stereo pair (set at the input module), the left and right channels are automatically routed to the left and right outputs on the AV-P2. If the selected channel is not part of a stereo pair, the selected mono channel's audio is routed to both the left and right outputs. The analog output level for each channel is set with front-panel DIP switches.
AV-P2 modules can be connected in any combination of serial or parallel connections, using Pro16 A-Net Distributors. There is no limit to the number of devices that can be daisy chained, or to the number of parallel splits in a single system. The AV-P2 is compatible with all Pro16 Series products and can be used in any combination with A-16II and A-16R Personal Mixers, the AN-16/o Output Module, and the A-16D and A-16D Pro Distributors.
Audio is distributed to the AV-P2 over standard Cat-5e cables, using Aviom's A-Net digital audio protocol which supports plug-and-play installation, real-time distribution with sub-millisecond latency, and long cable runs up to 500ft/150m. Power can be supplied to the AV-P2 with an external DC power supply or over the Cat-5e cable (with an A-Net Distributor).
The AV-P2 includes reversible mounting flanges. Two AV-P2 modules can be mounted side by side on a standard 1U rack tray.
|Audio Outputs||2, impedance balanced line-level
5.0 mm Euroblock connectors, female, panel- mount
2 male Euroblock connectors supplied in box
Screw terminals: Audio +; Audio -; Ground
|Channel Selection||16-position rotary switch|
|D/A Conversion||48kHz, 24-bit|
|Output Levels||Maximum Output Level: +18dBu
Output Level Trim from 0dB to -35.9dB in 1.5dB steps;
6-position DIP switch, per channel
|Indicators||LEDs; red: Power, green: A-Net Active, yellow: Stereo Pair|
|Output Impedance||100 ohms|
|Signal to Noise
|93dB typical, A/D to D/A
Measured from AN-16/i Input Module to AV-P2
|Freq. Response||4Hz-22kHz +0.2dB/-3dB|
|THD +N||-93dB at -10dBFS|
|Crosstalk||-85dB at 1kHz|
|Bit Error Rate (BER)||10-12|
|Digital Connections||A-Net In: 1; A-Net Out: 1; RJ45 connectors|
|Pro16 A-Net®||Uses unshielded Cat-5e UTP (or better) cable|
|Latency||<0.880 msec (measured from analog input to analog output)|
|External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm, locking, center pin hot
|Dimensions||7.45" (189.2 mm) wide x 7" (177.8 mm) deep; 1U high|
|Weight||3.4 lbs (1.54 kg)|