Auckland  09 414 0477
Wellington  04 801 9494
02419

Aviom AN-16/i-m

Aviom AN-16/i-m
larger imageMove mouse over the image to magnify
WAS NZ $4,849.00 NZ $4,503.00 Save NZ $346.00 Excl GST
Qty.

Product Highlights

  • Sixteen high quality mic preamplifiers, with 24-bit A-to-D converters
  • 48-volt phantom power on each channel
  • XLR mic or 1/4-inch TRS balanced line-level inputs on combo jacks
  • Continuously variable gain, phase reverse, and 85Hz rolloff per channel
  • Built-in passive mic splitter
  • Balanced insert send and return jacks (1/4-inch TRS)

The AN-16/i-M Mic Input Module is a 16-channel Pro16 input device with sixteen high-quality mic preamps and 24-bit A-to-D converters. It’s a great front end for a personal monitor mixing system when you need to plug your mic- and line-level input sources into the input module first and then continue on to the mixing console using its built-in splitter.

To create a digital snake, connect the AN-16/i-M to a Pro16 output device like the AN-16/o v.4 Output Module.

Each AN-16/i-M channel contains a three-segment level meter, a continuously variable gain knob, phase reverse switch, 48-volt phantom power, and a rumble filter with an 85Hz rolloff. In addition, each pair of channels can be Stereo Linked for stereo operation in a Pro16® personal mixing system.

 

Rear-panel Connectivity

The rear panel of the AN-16/i-M contains a host of professional connectivity features. Each channel has a combo jack that can accept either XLR mic or 1/4-inch line-level (balanced or unbalanced) inputs. Sixteen passive mic Thru connectors create a built-in microphone splitter. Balanced insert points with separate 1/4-inch Send and Return jacks allow easy interfacing with external processing devices. The sixteen insert Sends can also be used as a set of post-gain direct audio outputs. The AN-16/i-M uses an internal power supply with a standard IEC power connector.

Two parallel A-Net outputs allow the AN-16/i-M to send A-Net data to multiple destinations, allowing for simultaneous patching to a monitor console and a front-of-house console. Both A-Net outputs feature heavy duty Neutrik® EtherCon® RJ45 connectors. The built-in A-Net Expansion jack allows two 16-channel A-Net streams to be combined onto a single cable (in 32x0 or 16x16 configurations), and the AN-16SBR System Bridge can be used to combine up to four 16-channel streams onto a single cable in a variety of bidirectional configurations when creating larger digital snake systems.

As with all Pro16 Series products, Cat-5e cable runs of up to 500 feet (150 meters) are possible between devices.

Audio Inputs 16, balanced mic- or line-level, XLR combo connector
XLR Input
(mic/line)
Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio -
TRS Line Inputs, &
Send/Return
Tip: Audio +; Ring: Audio -; Sleeve: Ground
Audio Thru XLR; Pin 1: Ground; Pin 2: Audio +; Pin 3: Audio -
Direct coupled passive throughput
Insert Send Impedance balanced; Nominal level: 0dBu; Peak
Level (A/D clip point): +14dBu
The Insert Send connector is a line output in the signal path post gain, post filter, and post phase controls.
Insert Return TRS balanced; Nominal level: 0dBu; Peak Level
(A/D clip point): +14dBu
The Insert Return connector is a line input to the signal path that is pre A/D conversion.
Analog to Digital Conversion 48kHz sample rate, 24 bit
Operating Level +4dBu
Frequency Response 4Hz-22kHz
A-Net Output One Category 5 (RJ45 connector)
A-Net Expansion One Category 5 (RJ45 connector)
Gain Range Mic: +6dB to +60dB; Line: -15dB to +36dB
Channel LED Indicators Signal Present and Clip, per channel
Line Inputs Impedance: 48k ohms
Metering LEDs; green: Signal Present, red: Clip; per channel
Stereo Operation Stereo Link, per channel pair;
Two-position switch (Normal, Link)
Maximum Input Level Mic: +14dBu; Line: +28dBu
Input Impedance Mic: 2.4k ohms; Line (TRS): 33k ohms;
Insert Return: 39k ohms
A/D Freq. Response -0.1dB @ 20kHz (-0.4dB @ 20.0kHz, measured
from Mic or Line in)
-3dB @ 1.5Hz (-3dB @ 2.0Hz, measured from Mic or Line in)
THD +N < 0.003%
Crosstalk -90dB
Bit Error Rate (BER) 10(-12)
Signal to Noise (unweighted) A/D: -105dB Reference = +14dBu (A/D clip point) Send jack: -113dB (Gain = minimum)
EIN (Equivalent Input Noise) -128dBu
(Rs = 150 ohms, 20kHz BW, Gain = +60dB)
CMRR (Common Mode Rejection Ratio) 80dB @
120Hz (Gain = +60dB)
Low Cut Filter -3dB @ 85Hz, -18 dB per octave
Phantom Power +48 volts, per channel, switch with LED
Digital Outputs A-Net: 2 (Main and Aux); A-Net Expansion: 1
Pro16 A-Net A-Net Expansion combines two A-Net streams (32 channels of audio) onto one Cat-5e cable uses unshielded Cat-5e UTP (or better) cable
Latency <0.880 msec (measured from analog input to analog output)
Power Supply Internal, universal switching type; IEC jack
Voltage 100-240VAC, 50-60Hz, 60W; Fuse: 250VAC, F4AL
Dimensions 19" x 9.25" (482.6 x 234.95 mm); 3U high
Weight 12 lb(5.44 kg)
Options AN-16SBR System Bridge; used to combine up to four A-Net streams for transmission over one Cat-5e cable
0

Signup For Our Newsletter

Subscribe for the latest product news, special offers and invitations.

Give Us Your Feedback

We would love to hear what you think of our website and your experiences with our company. Drop us a line here.

Contact Us 

Auckland: 09 414 0477
Wellington: 04 801 9494

Australia: 1300 472 344

fbtw